 Nine Event Timer - The ET9 Pattern Controller is a microprocessor based nine event timer to control
glue gap or stitch adhesive patterns at fixed line speeds. The ET9 accepts two
trigger inputs and provides power output to four independent applicator head
groups. Nine pattern setups can be stored in memory when power is off.
When integrated into a Slautterback hotmelt applicator system, the ET9
controls adhesive deposition in a wide variety of fixed speed product assembly
and packaging applications. Typical applications include carton and case
sealing, pallet load stabilization, cap lining and labeling.
The ET9 functions according to a programmed pattern setup. A pattern setup
corresponds to the adhesive deposition of up to four head groups required for a
specific application. The setup contains the timing sequence of up to nine glue
or gap events per head group. Glue events may be stitched, resulting in pattern
versatility and adhesive savings.
The ET9 controls up to four independent adhesive applicator head groups. A
head group consists of one to four E100 or ML400 style valves, or up to sixteen
E900TM
style valves. Input signals trigger the ET9 to activate the pattern setup,
transmitting output power to the head groups.
The ET9 is easy to install and operate. Programming and adjusting pattern
setups are simple with convenient toggle switches. An accessible internal
terminal strip facilitates wiring of input signal and power output options. All
circuits are optically isolated for electrical noise immunity.
A complete pattern control package consists of the ET9 and one or two photo
eye sensors. For increased pattern placement accuracy, a DC Driver or HD2a Head
Driver should be included.
Features:
- Accurate placement of up to four independent adhesive patterns at
fixed line speeds
- Stitch patterns for adhesive cost savings
- Power-off memory for nine pattern setups
- Head group test switch
- Two timers in one: Controls four independent head groups from two
separate inputs
- Adjustment of any pattern setup while in operation
- Glue and gap events of up to 9.999 sec.
- One ms resolution; ±0.5 ms accuracy and repeatability
- Program lock security
- Simple toggle switch programming and operation
- Controls air solenoids and other parent machine time dependent
functions
- Easy to read four digit time display
Specifications:
PHYSICAL
Gasket sealed, dust proof and water resistant metal enclosure which meets
NEMA 4 specifications
Operating Temperature
32-150 °F (0-66 °C)
Storage Temperature
-22-158 °F (-30-70 °C)
PERFORMANCE
Event Duration Range
0.001-9.999 sec.
Resolution
One ms
Accuracy and repeatability: ±0.5 ms
NOTE:Ten events are possible when "zero" is used as a numeric
value for the tenth event.
|
ELECTRICAL
Power Requirements
100-115 VAC, 25 W, 50/60 Hz, or
200-230 VAC, 25 W, 50/60 Hz
One or Two Trigger Inputs
Voltage requirements
5- 24 VDC, 4-25 mA.
This voltage can be supplied from ET9 on-board power supply or from an external source.
Type
Photoeye sensors;mechanical triggers not recommended
Mode
"One Shot"- Sequence initiated and completed with one trigger input.
"Duration"- Sequence initiated and continued as long as trigger signal is engaged
Assignment to Head Groups
Trigger #1 signals head groups one and two
Trigger #2 signals head groups three and four
NOTE: Head groups three and four may be connected to one and two and assigned to Trigger #1.
Power output switching relays
5-60 VDC, 3A, or
60-230 VAC, 5 A
Head Group Capacity
1-4 head groups
Number of heads in head groups
"E100 Style Valves"- up to four
"E900TM Style Valves"-up to eight with 115 VAC power or up to sixteen with DC power or @#) VAC power
Power supply output
12 VDC, 200 mA, or
24 VDC, 200 mA
Power provided for photoeye triggers and to signal head drivers
|
|
